Set An Appointment

 

They are making a few great points relating to How to Install a Bathtub overall in the content in the next paragraphs.

Installing a bathtub isn't specifically rocket science, yet it does need solid plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a new one is also a moderately challenging project. If the old bathtub is conveniently accessible, the task can relocate rapidly; if you have to open a wall to remove the old bathtub and place the brand-new bathtub, the job is much harder. In either case, the project is within a home handyman's skills, although you will certainly need an assistant to move out the old tub as well as embeded in the brand-new one. Ensure you have actually certified yourself for the task and also fit attempting it. As opposed to working with a service provider to take over a halfway-completed task, it is far better to take into consideration employing one before you start. Opportunities are you may need a professional plumber to make tube connections.
This write-up will certainly assist you set up a brand-new tub in your restroom if you have actually currently purchased a new tub and also do not need to transform the setup of your previous supply of water pipes.
Your tools and also material list must make up the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Planning for the Installation

Firstly, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to make certain that if the faucet features a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps unit to prevent pressure on the tub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you use every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last position.

 

 

Removing Old Touches

If you require to change old taps with brand-new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, switch on the taps to drain any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a cloth all set for the staying water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming throughout this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
Before carrying on to fit the brand-new taps, compare the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.

 

 

Mounting the Bath tub

Using both wood boards under its feet, place the bathtub in the needed placement. The wooden boards are handy in evenly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as readjusting the feet on the tub till the level checks out degree.
To install faucets, fit all-time low of the furthest adaptable tap adapter to the ideal supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Activate the supply of water as well as examine all joints as well as new pipework for leakages and also tighten them if necessary. Fill the bath tub and likewise inspect the overflow electrical outlet and also the normal outlet for leaks.
Finally, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub should wait till the bath tub has actually been made use of at least once as this will settle it right into its last position.

 

 

Suitable New Taps

If the tails of the new taps are plastic, after that you will need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end gives a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in area in between the tap and also the sink. Safeguard the tap in place with the producer provided backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal tap adapters. The former kind ought to be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Tub

In the location where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a rigid seal, causing the water to permeate the wall in between the bath and the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your components and also installations. They are offered in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bath tub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can break relatively early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly readily available on the market. It is advisable to fit the tiles making use of waterproof or water-proof sticky and cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Hopefully you liked our article about How to Install a Bathtub Yourself. Thanks so much for spending some time to read through our short article. Don't hesitate to take the time to distribute this blog if you enjoyed reading it. Thank you for your time spent reading it.

Tap dripping? Phone!